Silicon photonics

Research & publications.

Graduate research at the University of Utah spanning thermal modeling of integrated optoelectronics, silicon photonics, design-for-test, and calibration.

Publications

Selected publications and thesis work

Papers, accepted manuscripts, and thesis work on silicon photonics test, calibration, variation analysis, and thermal abstraction.

2026

IEEE International Test Conference (ITC) · accepted manuscript

Defect-Oriented, Optimization-Driven ATPG for Silicon Photonic Integrated Circuits

Lawrence Schlitt, Priyank Kalla, and Steve Blair

Evaluates defect-oriented test generation using finite illustrative circuit models and nonlinear replay of candidate tests.

Read accepted manuscript (PDF)
View SiPh-ATPG on GitHub

The repository identifies the manuscript above. Its modeled detection results do not establish hardware detection probabilities.

2026

IEEE European Test Symposium (ETS)

Scalable Design-for-Calibration of Programmable Silicon Photonics

Lawrence Schlitt, Priyank Kalla, and Steve Blair

Evaluates calibration using synthetic mesh and microring circuit models. Hardware-write accounting describes simulated actuator updates.

Read author-hosted paper (PDF)
View SiPh-Calibration on GitHub

This repository accompanies the 2026 paper above. The experiments use synthetic circuit models.

2025

IEEE International Test Conference (ITC)

Silicon Photonic Test-Point Selection by Integrating Design Parameters with Hypergraph Partitioning

Lawrence Schlitt, Pratishtha Agnihotri, Priyank Kalla, and Steve Blair

Evaluates risk-weighted test-point selection and estimated access overhead on three illustrative circuit topologies.

View publication
Research code on GitHub

The repository documents a newer partitioning backend and implementation differences from the published experiments; results may differ.

2025

IEEE European Test Symposium (ETS)

Design-for-Test and Calibration for Silicon Photonics using Ring Resonators and Wavelength Division Multiplexing

Pratishtha Agnihotri, Lawrence Schlitt, Priyank Kalla, and Steve Blair

Evaluates a ring-resonator and WDM test-access architecture in Lumerical simulations, including a photonic neural-network subcircuit.

View publication

2023

IEEE Latin American Test Symposium (LATS)

Abstractions for Modeling the Effects of Wall Surface Roughness in Silicon Photonic Microring Resonators

Pratishtha Agnihotri, Lawrence Schlitt, Priyank Kalla, and Steve Blair

Models wall-surface roughness using notch perturbations and compares predicted microring resonance shifts with FDTD simulations.

View publisher record (DOI)

2016

International Conference on VLSI Design

A Methodology for Thermal Characterization Abstraction of Integrated Opto-electronic Layouts

Lawrence M. Schlitt, Priyank Kalla, and Steve Blair

Introduces abstraction techniques for thermal-aware reasoning in hybrid opto-electronic layouts.

View publication

2016

University of Utah thesis

Thermal Characterization Abstraction for Integrated Optoelectronics

Lawrence M. Schlitt

Graduate thesis focused on tractable thermal modeling for integrated optoelectronic systems.

View thesis record

Research

Photonics, CAD, and test methodology

My doctoral work brought together access, calibration, and test synthesis for silicon photonics. My earlier master’s work focused on thermal abstraction for integrated optoelectronics.

Silicon Photonics

Design-for-test and calibration

Studies testability, ring-resonator-based tuning, and partitioning-based test access for proposed post-fabrication testing and calibration.

EDA Methods

Photonic design automation

Develops layout, thermal, and circuit abstractions for reasoning about silicon photonic systems.

Robustness

Thermal and variation modeling

Studies how temperature gradients, surface roughness, and manufacturing shifts affect behavior in microring resonators and integrated optoelectronic layouts.

Verification

ATPG, DFT, and testability analysis

Studies defect models, test access, and calibration-aware architectures using analytical and simulated photonic circuits.

Engineering methods

Silicon photonic design-for-testCalibration-aware architecturesRing resonator analysisWavelength division multiplexingHypergraph partitioningThermal characterization abstractionManufacturing variation modelingVerification-oriented reasoning

From device behavior to engineering decisions

Device physics, test planning, and manufacturing constraints inform the same design process.

Layout and device modeling

Connects physical layout, material properties, and device models to thermal and optical behavior.

Test-access planning

Uses circuit structure and partitioning to study where test access can be added under resource constraints.

Variation and tuning

Studies thermal sensitivity, fabrication variation, observability, and tuning through analytical models and simulation.

Master’s research · 2016

Thermal Characterization Abstraction for Integrated Optoelectronics

M.S., Electrical and Computer Engineering · University of Utah. Thermal modeling of integrated electronic and photonic systems.

My master’s research examined how heat from nearby electronics changes integrated photonic-device behavior. The work connects physical layout and material properties to temperature-dependent optical response.

A layout-to-optics modeling workflow
  1. GDSII layout

    Geometry and material layers

  2. Thermal network

    Layered resistance model

  3. Temperature field

    Numerical thermal solution

  4. Optical response

    Refractive index and phase

Method
A compact thermal resistance network represents the material layers. A layered 2.5D model uses an alternating-direction implicit finite-difference solver to compute temperatures, which are then related to ring-resonator refractive-index and phase changes.
Contribution
The related 2016 VLSI Design paper demonstrates this layout-based abstraction through simulation using the GDSII layout of a fabricated optical-logic chip and a simulated heat source. At publication, comparison with laboratory measurements was identified as follow-on work.

Academic projects

Research in practice

The engineering problems, methods, and outcomes behind these lines of academic work.

Silicon photonic test-point selection

Photonic circuits need observability strategies that respect both physical structure and performance behavior.

Approach: Integrated design parameters with hypergraph partitioning to study risk-weighted test-point selection under resource constraints.

Outcome: Demonstrates modeled risk coverage and estimated access overhead on three illustrative circuit topologies, rather than measured fault-detection coverage.

Read related paper
Research code on GitHub

The repository documents a newer partitioning backend and implementation differences from the published experiments; results may differ.

Ring-resonator and WDM test-access architecture

Fabrication and environmental variation can move photonic devices outside their intended operating window.

Approach: Co-developed a ring-resonator and WDM test-access architecture and evaluated it in Lumerical circuit simulations.

Outcome: The simulations distinguish defect-free and faulty responses in a photonic neural-network subcircuit. They do not demonstrate measured hardware performance or a complete automated calibration flow.

Read related paper

Thermal abstraction for integrated optoelectronics

Full coupled thermal and electromagnetic simulation is expensive for hybrid opto-electronic stacks.

Approach: Built a layout-based thermal-resistance abstraction with a numerical solver, relating computed temperatures to optical-device behavior.

Outcome: Demonstrates thermal simulation on an optical-logic chip layout, relating calculated temperatures to ring-resonator phase changes. Laboratory comparison was follow-on work in the 2016 paper.

Read related paper

Wall-roughness modeling in microring resonators

Wall-surface roughness changes the behavior of silicon photonic microring resonators.

Approach: Modeled wall roughness as notch perturbations to estimate resonant-wavelength shifts.

Outcome: Predicted microring resonance shifts were compared with full-scale FDTD simulations. This comparison concerns simulated optical behavior.

View publisher record (DOI)

Research software

Code and associated papers

Public research software accompanying the 2026 calibration and test-generation studies listed above.

2026 · IEEE International Test Conference (ITC) · accepted manuscript

SiPh-ATPG

Related paper: Defect-Oriented, Optimization-Driven ATPG for Silicon Photonic Integrated Circuits.

Read accepted manuscript (PDF)
View SiPh-ATPG on GitHub

The repository identifies the manuscript above. Its modeled detection results do not establish hardware detection probabilities.